Copyright © tutorialspoint.com
If from is not NULL, and the underlying protocol provides the source address, this source address is filled in. The argument fromlen is a value-result parameter, initialized to the size of the buffer associated with from, and modified on return to indicate the actual size of the address stored there.
The recv() call is normally used only on a connected socket (see connect(2)) and is identical to recvfrom() with a NULL from parameter.
All three routines return the length of the message on successful completion. If a message is too long to fit in the supplied buffer, excess bytes may be discarded depending on the type of socket the message is received from.
If no messages are available at the socket, the receive calls wait for a message to arrive, unless the socket is nonblocking (see fcntl(2)), in which case the value -1 is returned and the external variable errno set to EAGAIN. The receive calls normally return any data available, up to the requested amount, rather than waiting for receipt of the full amount requested.
The select(2) or poll(2) call may be used to determine when more data arrives.
The flags argument to a recv() call is formed by ORing one or more of the following values:
|Enables non-blocking operation; if the operation would block, EAGAIN is returned (this can also be enabled using the O_NONBLOCK with the F_SETFL fcntl(2)).|
|This flag specifies that queued errors should be received from the socket error queue. The error is passed in an ancillary message with a type dependent on the protocol (for IPv4 IP_RECVERR). The user should supply a buffer of sufficient size. See cmsg(3) and ip(7) for more information. The payload of the original packet that caused the error is passed as normal data via msg_iovec. The original destination address of the datagram that caused the error is supplied via msg_name.|
For local errors, no address is passed (this can be checked with the
cmsg_len member of the
cmsghdr). For error receives, the
MSG_ERRQUEUE is set in the
msghdr. After an error has been passed, the pending socket error
is regenerated based on the next queued error and will be passed
on the next socket operation.
The error is supplied in a sock_extended_err structure:
|ee_errno contains the errno number of the queued error. ee_origin is the origin code of where the error originated. The other fields are protocol specific. The macro SOCK_EE_OFFENDER returns a pointer to the address of the network object where the error originated from given a pointer to the ancillary message. If this address is not known, the sa_family member of the sockaddr contains AF_UNSPEC and the other fields of the sockaddr are undefined. The payload of the packet that caused the error is passed as normal data.|
|For local errors, no address is passed (this can be checked with the cmsg_len member of the cmsghdr). For error receives, the MSG_ERRQUEUE is set in the msghdr. After an error has been passed, the pending socket error is regenerated based on the next queued error and will be passed on the next socket operation.|
|This flag requests receipt of out-of-band data that would not be received in the normal data stream. Some protocols place expedited data at the head of the normal data queue, and thus this flag cannot be used with such protocols.|
|This flag causes the receive operation to return data from the beginning of the receive queue without removing that data from the queue. Thus, a subsequent receive call will return the same data.|
|Return the real length of the packet, even when it was longer than the passed buffer. Only valid for packet sockets.|
|This flag requests that the operation block until the full request is satisfied. However, the call may still return less data than requested if a signal is caught, an error or disconnect occurs, or the next data to be received is of a different type than that returned.|
recvmsg() call uses a
msghdr structure to minimize the number of directly supplied parameters. This
structure has the following form, as defined in
|Here msg_name and msg_namelen specify the source address if the socket is unconnected; msg_name may be given as a null pointer if no names are desired or required. The fields msg_iov and msg_iovlen describe scatter-gather locations, as discussed in readv(2). The field msg_control, which has length msg_controllen, points to a buffer for other protocol control related messages or miscellaneous ancillary data. When recvmsg() is called, msg_controllen should contain the length of the available buffer in msg_control; upon return from a successful call it will contain the length of the control message sequence.|
The messages are of the form:
|Ancillary data should only be accessed by the macros defined in cmsg(3).|
|As an example, Linux uses this auxiliary data mechanism to pass extended errors, IP options or file descriptors over Unix sockets.|
|The msg_flags field in the msghdr is set on return of recvmsg(). It can contain several flags:|
|indicates end-of-record; the data returned completed a record (generally used with sockets of type SOCK_SEQPACKET).|
|indicates that the trailing portion of a datagram was discarded because the datagram was larger than the buffer supplied.|
|indicates that some control data were discarded due to lack of space in the buffer for ancillary data.|
|is returned to indicate that expedited or out-of-band data were received.|
|indicates that no data was received but an extended error from the socket error queue.|
|EAGAIN||The socket is marked non-blocking and the receive operation would block, or a receive timeout had been set and the timeout expired before data was received.|
|EBADF||The argument s is an invalid descriptor.|
|A remote host refused to allow the network connection (typically because it is not running the requested service).|
|EFAULT||The receive buffer pointer(s) point outside the processs address space.|
|EINTR||The receive was interrupted by delivery of a signal before any data were available.|
|EINVAL||Invalid argument passed.|
|ENOMEM||Could not allocate memory for recvmsg().|
|The socket is associated with a connection-oriented protocol and has not been connected (see connect(2) and accept(2)).|
|The argument s does not refer to a socket.|
POSIX.1-2001 only describes the MSG_OOB, MSG_PEEK, and MSG_WAITALL flags.
According to POSIX.1-2001, the msg_controllen field of the msghdr structure should be typed as socklen_t, but glibc currently (2.4) types it as size_t.
Copyright © tutorialspoint.com